Sabtu, 27 Desember 2014

Canon Error Code 2

E013
•The PLL lock is released because waste toner motor is locked up,etc.
•The micro switch employed to detect clogging of waste toner is activated.
•The waste toner case is detected full.
E014
•The PLL lock of the fixing/feeding motor is released.
•Excess current of the feeding motor is detected.
E015
•Clock pulses of the pick-up/duplexing/developing motor fails to be generated or
be detected.
•Excess current of the pick-up/duplexing/developing motor is detected.
E016 Excess current of the reciprocating motor
of the photosensitive drum cleaner unit is detected.
E017 The PLL lock of the drive motor of the holding tray unit is released.
E018 The PLL lock of the drive motor of the oil removing roller is
E019 The waste toner case is detected full although it is not.
E020 The developer fails to be replenished with starter developer properly.
Read More..

Canon Error Code

E051 The home position of the side registration cannot be detected

within a specific time.

E054 The home position of the duplexing unit feed roller cannot bedetected.

E055 The horizontal registration guide of the duplex unit exceeds its

maximum travel distance.

E060 The home position of the primary corona wire cleaner cannot be

detected within a specific time.

Relateted charging

E061 Specific potential is not be required or the limiter is activated as the

potential is controlled.

E062 The photosensitive drum temperature does not reach a specific

value due to a fault in the photosensitive drum heater, etc.

E063

The home position of the transfer corona wire cleaner cannot be

detected.

An error code is

not to be

indicated.

E064 The setting value for the output from the microcomputer

considerably deviates from the control value of the actual output.

E065 High voltage leakage from the primary corona assembly is

detected.

E066 Signals from the temperature/humidity sensor cannot be detected.

E067

Two or more faults in the primary/ pre (post)-transfer/ transfer/

separation high voltage are detected (including power output

stoppage, electric leakage from the primary corona assembly).

E068 High voltage leakage from or an open circuit in the separation

corona assembly is detected.

E069 High voltage leakage from or an open circuit in the transfer corona

assembly is detected.

E070 The home position of the transfer drum cannot be detected within a specific time.

E071 An image leading edge signal cannot be detected within a specifictime.

E072 A fault in the main motors such as the transfer drum motor, etc.
Read More..

Rabu, 09 April 2014

Download Service Manual Epson R230 and R220


Before run adjustment program or software resetter Epson Stylus Photo R220 and R230, set date setting in your computer to 12 January 2006. Appearance of adjustment program Epson stylus photo R220 and R230 like adjustment program for Epson C45. Your Epson Stylus Photo R220 and R230 must be installed correctly in your computer before using the software otherwise so this software resetter will not be used.
Here how to use the software

* Download and extract downloaded software and run it.
* Click accept button.
* Set model name, port selection and destination setting and equal
to your printer.
* Click Maintenance Tab.
* Check mark waste ink pad counter.
* And the clear the protection counter (reset counter to zero)
* Then click Ok, Ok
* done

=> adjusment program Epson R220 - R230
=> adjusment program Epson R270
Download manual service
and any way if epson r230 blinking you can use SSC
klik at => SSC 4.3 and there are tutorial and how to use it.

How to use the SSC Service Utility

Please to be Patient and if any one want something else please give me comment down here Ok
thanks guys 4 all comment
Read More..

Jumat, 04 April 2014

Printer Driver Canon PIXMA iP7220

Compatibility and system requirements :
- Windows 8
- Windows 7
- WIndows Vista
- Windows XP

- all drivers Support 32bit and 64bit
Download link Canon PIXMA iP7220 Printer drivers
link

Mac OS
Mac OS X v10.8
Mac OS X v10.7
Mac OS X v10.6
Mac OS X v10.5
Link download
Read More..

Minggu, 30 Maret 2014

How to Reset Your Canon Pixma IP1880

Waste Ink Counter Reset Manual for Service mode
1. Turn On iP1880
2. Push and Hold Resume button about 2 minutes
3. Release Resume button
4. Printer back to normal again
Read More..

Selasa, 25 Maret 2014

 EPSON Reset Stylus Color 400, 600 EPSON Stylus Color 400, 600EPSON Stylus Color 400, 600 EPSON Stylus Color 400, 600

Pressing and holding LOAD/EJECT and CLEANING buttons, press POWER button and hold it until You will see blinking INK OUT and PAPER OUT leds. Pressing and holding LOAD / EJECT and CLEANING buttons, press POWER button and hold it until You will seeblinking INK OUT and PAPER OUT leds.
Release all buttons. Release all buttons.
In 2-3 seconds time press and release LOAD/EJECT button. In 2-3 seconds time press and release LOAD / EJECT button.

Read More..

Kamis, 20 Maret 2014

Resetter Epson SP 1390




Easy to use and small file





How to use resetter Epson Sp 1390

1. Change the date of your PC to the October 4, 2007
2. Run the reset program by double-clicking "AdjProg.exe"
3. Click "Particular adjustment mode"
4. Select "Waste ink pad counter"
5. Click "Check and Initialization"
6. Click "Finish"
7. Turn off the printer
8 Turn on the printer
9. Good luck
Read More..